Yes, there are several commands to run and lots of output on the screen, but rebuilding the BCD is a very straightforward process. Just follow the instructions exactly and you'll be fine. Important: The following instructions apply to,,, and. Similar problems can exist in but since boot configuration information is stored in the boot.ini file, and not the BCD, correcting issues with boot data involves a completely different process. See for more information. How to Rebuild the BCD in Windows Rebuilding the BCD in Windows should only take around 15 minutes and, while it isn't the easiest thing you'll ever do, it isn't too tough either, especially if you stick to the directions below.

Select Command Prompt. Type the following command and hit Enter: bootrec /rebuildbcd. Now there are two scenarios you can encounter: (1)Total identified Windows installations: 0. Go to Step 5. (2)Total identified Windows installations: 1. Type Y, hit Enter and reboot your computer. Jul 01, 2015 Hi, Something must have scrambled your HDD.successfully scanned 0 installations doesn't make sense. Searh online for a bootable CD version of a DiskManagement.

• Start if you're using Windows 10 or Windows 8. See if you're not sure how to do that. Start if you're using Windows 7 or Windows Vista. See the How to Access the System Recovery Options Menu section in that link I just gave you for help if this is your first time using the menu. • Open from Advanced Startup Options or System Recovery Options menu.

Note: The Command Prompt available from these diagnostic menus is very similar to the one you may be familiar with within Windows. Also, the following procedure should work identically in Windows 10, 8, 7, and Vista. • At the prompt, type the bootrec command as shown below and then press Enter: bootrec /rebuildbcd The bootrec command will search for Windows installations not included in the Boot Configuration Data and then ask you if you'd like to add one or more to it. • You should see one of the following messages at the. Option 1 Scanning all disks for Windows installations. Please wait, since this may take a while. Photoshop Cs6 Deutsche Sprachdatei Download Skype.

Successfully scanned Windows installations. Total identified Windows installations: 0 The operation completed successfully. Option 2 Scanning all disks for Windows installations. Please wait, since this may take a while.

Successfully scanned Windows installations. Total identified Windows installations: 1 [1] D: Windows Add installation to boot list? Yes/No/All: If you see: Option 1: Move on to Step 5. This result most likely means that Windows installation data in the BCD store exists but bootrec couldn't find any additional installations of Windows on your computer to add to the BCD. That's fine, you'll just need to take a few extra steps to rebuild the BCD.

Option 2: Enter Y or Yes to the Add installation to boot list? Question, after which you should see a The operation completed successfully message, followed by a blinking cursor at the prompt.

Finish up with Step 10 toward the bottom of the page. • Since the BCD store exists and lists a Windows installation, you'll first have to 'remove' it manually and then try to rebuild it again. At the prompt, execute the bcdedit command as shown and then press Enter: bcdedit /export c: bcdbackup The bcdedit command is used here to export the BCD store as a file: bcdbackup. There's no need to specify a. The command should return the following on screen, meaning the BCD export worked as expected: The operation completed successfully.

• At this point, you need to adjust several for the BCD store so you can manipulate it. At the prompt, execute the exactly like this: attrib c: boot bcd -h -r -s What you just did with the attrib command was remove the,, and attributes from the file bcd. Those attributes restricted the actions you could take on the file. Now that they're gone, you can manipulate the file more freely - specifically, rename it. • To rename the BCD store, execute the ren command as shown: ren c: boot bcd bcd.old Now that the BCD store is renamed, you should now be able to successfully rebuild it, as you tried to do in Step 3.

Note: You could delete the BCD file entirely since you're about to create a new one. However, renaming the existing BCD accomplishes the same thing since it's now unavailable to Windows, plus provides you yet another layer of backup, in addition to the export you did in Step 5, if you decide to undo your actions.

• Try rebuilding the BCD again by executing the following, followed by Enter: bootrec /rebuildbcd which should produce this in the Command Prompt window: Scanning all disks for Windows installations. Please wait, since this may take a while.

Successfully scanned Windows installations. Total identified Windows installations: 1 [1] D: Windows Add installation to boot list? Yes/No/All: meaning that the BCD store rebuild is progressing as expected. • At the Add installation to boot list? Question, type Y or Yes, followed by the Enter key. You should see this on screen: The operation completed successfully.

Meaning that the BCD rebuild is complete. Assuming that an issue with the BCD store was the only problem, Windows should start as expected. If not, continue to troubleshoot whatever specific issue you're seeing that's preventing Windows from booting normally. Important: Depending on how you started Advanced Startup Options or System Recovery Options, you may need to remove a disc or before restarting.

Yep i tried this Woodenhorse: An old thread but feel like posting as this site come up as top ranked when googled, so heres my 2 cents for those who stumble accross this thread while searching for a solution. Had same issue today as many, atempted repair using vista disk but OS was detected, but clicked next anyway and the process started, and to my suprise it made a succesfull repair, while it rebooted a few times, from doing some research i found out that it doesn't allways work but there is a way around that also, select install instead of repair and it will detect your drive, select cancel and go back to the repair section, your OS will show up now. Cause of the BootMGR missing, most times virus or failing hdd, so if your system is behaving a little bit strange and slow get yourself a new hdd and clone the old one. In my case it was a virus which gave my system a BSD, unaware as I was out, traced back to an ebay competitors email lol, and thought kaspersky was good. And Kevin23 if you get the 'BOOTMGR' is missing error upon startup and your tried to do a system repair, but no drive was located with an OS, try this - 1. Try to hit the 'DEL' button upon startup and then try going into safe mode (so the necessary drivers are loaded) 2. Disconnect SATA cables (if any) 3.

Disconnect IDE cables 4. Re-connect everything when i re-connected everything back up, i was able to re-boot without any problems, and actually didn't have to do a system repair with the DVD. However, it took me hours to figure out what to do and was ready to lose my files just to do a fresh install. Glad it didn't go that way.

However, i had a laptop so there really wasn't anything to unplug cable wise. LS Let's see if we can get you going.

Keep looking at post as I will ADD links. If the previous method does not resolve the problem, you can rebuild the BCD store by using the Bootrec.exe tool in the Windows Recovery Environment. To do this, follow these steps: 1.

Put the Windows Vista installation disc in the disc drive, and then start the computer. Press a key when you are prompted.

Select a language, a time, a currency, and a keyboard or another input method, and then click Next. Click Repair your computer. Click the operating system that you want to repair, and then click Next. In the System Recovery Options dialog box, click Command Prompt. Type Bootrec /RebuildBcd, and then press ENTER. If the Bootrec.exe tool runs successfully, it presents you with an installation path of a Windows directory. To add the entry to the BCD store, type Yes.

A confirmation message appears that indicates the entry was added successfully. If the Bootrec.exe tool cannot locate any missing Windows installations, you must remove the BCD store, and then you must re-create it. To do this, type the following commands in the order in which they are presented.

Press ENTER after each command. Bcdedit /export C: BCD_Backup ren c: boot bcd bcd.old Bootrec /rebuildbcd 8. Restart the computer. Please Post Back. I tried the second edit ran Drive: boot Bootsect.exe /NT60 All o get the System cannot find the path specified. When i boot in command prompt though and type C:/ it access that drive i type in dir Volume in drive C has no lable volume Serial Number is B6C-9A2D Directory of C: File not found i typed notepad and file>open type * enter and got a directory empty. I just wanna backup my stuff:(.

I'm going to run Seatools to test my HD then iuno im going to try these 2 other linux distros see if i can get one to access my HD to copy to external (Gparted and Knoppix).